Always read the Operating Handbook before use and follow all
Safety Instructions
| Problem Solving - Blocked nozzles, Low Pressure, leaks etc. | 
998 kb |
| Important Safety info re Power Supply & Extention Cables |
184 kb |
| General Safety Information - Please Read |
329 kb |
Inspections
Pressure washers must be inspected according to the "Guidelines for Liquid
Spray Devices" at least every 12 months by a qualified person, to ensure
that continued safe operation is guaranteed. The results of the inspection are
to be recorded in writing. This can be done in the machine's Handbook.
Accident prevention
Kranzle pressure washers are designed for accidents to be impossible if used
correctly.
The operator must be notified of the risk of injury from hot machine parts and
the high pressure water jet and the Safety Information,
as part of the "Guidelines for Liquid Spray Devices" must be followed.
Warranty
The warranty covers material and/or workmanship related defects and does not
extend to ordinary wear.
Machines must be operated according to the operating instructions, supplied with
the machine, which form part of the warranty conditions.
Machines designed to be used in a horizontal position must not be operated in an
upright position.
Pressure washers sold directly to private customers are warrantied for a period
of 24 months. The manufacturers warranty for machines being used commercially or
industrial use is 12 months. However this can be extended by the supplier
to 24 months if the machine is regularly serviced by an Approved Kranzle Service
Agent. In the case of any warranty claim please have your machine together with
accessories and your purchase documents ready and contact your supplier or
ourselves.
Warranty is void in cases where the machine or any of the safety devices have
been modified, where non Kranzle replacement parts have been used that have not
been authorized by Kranzle or in the event that maximum temperature has been
exceeded. Damage caused to the machine by a contaminated or inadequate
water supply is not covered by the warranty (See Operator Manuals &
Instructions) - this also applies to damage caused by an inadequate power supply
or the use of extension cables that are not 2.5mm cross section. The gun,
lance, nozzle, high pressure hose and O rings are considered to be wear parts
and are not included in this warranty.
Oil change
The oil in your high
pressure pump should be changed after approximately 40 hours of operation, or no
later than when it takes on a grey or milky colour. This colour change is due to
absorption of moisture by the oil due to high humidity and temperature
fluctuations which is not uncommon with typical locations of the pressure washer
during use. Leaking water seals in the pump will speed up the absorption
of water by the oil and should be replaced. The condition of the oil and
it's correct level at the oil sight glass should be checked prior to each
use. Oil seals only need replacing if oil is leaking from the
machine. If this occurs book your machine in for a service without delay.
BEWARE, many machine have a sealed oil bath and must not be over filled.
Always just cover the sight glass with the machine in its horizontal position
(where applicable) or fill to between the Max and Minimum marks on the oil
bottle or dip stick where appropriate to the machine.
Change the oil after 40 to 50 operating hours. Further oil changes are only required when the colour of the oil goes milky due to moisture or water leaks. |
HD9/80, HD10/100E, HD10/100S, HD12/130S HD690S, B12/130, B13/150, B10/200, B170T, B200T, Power-Jet115, Profi-Jet90, Profi-Jet100, Prrofi-Jet130, Profi-Jet150, Profi-Jet 180, Junior120, Junior140, K105, K130, K150, K1120/K1120T, K1150/K1150T, K1151/T, K100, K115, K125, K135, K155, K185, K145T, K175T, K205T, K160TST, K195TST, Profi160TST, Therm 630/635 |
The first oil change should be carried out after approx 50 operating hours the every 1000 operating hours. Use only |
B16/220, D16/220, B230T, B240T, B270T, K3170TST, K3200TST, K3250TST, K3270TST, Q11/140TS/T, Q599TST, Q799TST, Q800TST, Q1000TST, Q1200TST W15/200(220), W19/160 |